Squarespace Site Server v5.11.81 (http://www.squarespace.com/)http://www.sturdell.com/picture/Complex%20Waterline.jpg?pictureId=8376132<h2>Complex Waterline</h2> <p>Complex waterline angles made this one tough! Sturdell delivered by doing the following:</p> <div id="_mcePaste"></div> <div id="_mcePaste"></div> <div id="_mcePaste"> <ul> <li>Saw cut the corners to finish</li> <li>Blanchard Ground top &amp; bottom</li> <li>Interpolated the inside diameter</li> <li>Milled the sides to size and square - Added lift-holes &amp; chamfers</li> <li>Gundrilled to print with the aid of our 3D CAM software</li> <li>Delivered the job in 8 days from receipt of P.O.</li> </ul> </div>http://www.sturdell.com/picture/Days%20Saved.jpg?pictureId=8376133<p>&nbsp;</p> <h2>Days Saved</h2> <div>This customer used to spend two days each way in transit to obtain Gundrilling on his Plates</div> <div id="_mcePaste"></div> <div id="_mcePaste">Sturdell now provides plates fully machined and gundrilled - on his floor in 9 days complete.</div> <p>&nbsp;</p> <p>&nbsp;</p>http://www.sturdell.com/picture/5%20day%20turnaround.jpg?pictureId=8376134<h2>Quick Turnaround</h2> <div> <ul> <li>Over 16,000 lbs of material</li> <li>Ground, Milled Square with Lift-holes and Chamfers - all shipped in 5 days!</li> </ul> </div> <div id="_mcePaste"></div> <div></div> <p>&nbsp;</p>http://www.sturdell.com/picture/Complete%20in%208%20days.jpg?pictureId=8376138<h2>Complete in 8 days</h2> <p>&nbsp;</p> <div id="_mcePaste"> <ul> <li>Over 13,000 lbs of steel, 600 inches of Gundrilling with Taps &amp; Counterbores. Customer needed on his floor in 9 days. Here's what we did.&nbsp;</li> <li>First we cut this from a plate 84" x 145"</li> <li>Next we Blanchard Ground both of these plates to desired thickness</li> <li>Milling these &amp; adding Lift-holes was a breeze on our 35 HP boring mill</li> <li>Our Large gundrill tackled this one just fine, even adding the Counterbores and Taps right on the machine</li> </ul> </div> <p>&nbsp;</p>http://www.sturdell.com/picture/TieBar%20Spacing.jpg?pictureId=8376139<p>&nbsp;</p> <h2>Tie-Bar Spacing a Problem?</h2> <div id="_mcePaste"></div> <div id="_mcePaste">Molding machine not big enough for mold? We helped this customer around this problem he had.</div> <div id="_mcePaste"></div> <div id="_mcePaste"></div> <div id="_mcePaste">We cut the corner's off so the customer could fit this into a smaller molding machine he wanted to use for this tool.</div> <div id="_mcePaste"></div> <div id="_mcePaste">He could not find anyone to make clean machined edges for him to maintain the aesthetic value of the tool with his modifications.</div> <p>&nbsp;</p>http://www.sturdell.com/picture/Set%20of%209%20in%207%20days.jpg?pictureId=8376141<h2>Set of 9 in 7 days</h2> <div id="_mcePaste"></div> <div id="_mcePaste">Over 2,146 inches of waterlines and 162 taps.....7 days from P.O.</div>http://www.sturdell.com/picture/Rough%20Pocketing.jpg?pictureId=8376313<h2>Rough Pocketing</h2> <p>Our customer wanted to do "minimal machining" when he received these blocks. We took them to within .060" on the pockets and he finished them in a tenth the time. This let his machines do what their intended for. Making him money!</p>